如何合理控制干燥機設備中的氧氣

山東干燥設備合理控制干燥設備中的氧氣的方法：如果沒有氧氣，火將不會持續很長時間。因此，通過減少干燥設備中的氧氣，可以相應地降低火災風險，這是一個非常重要的預防措施。因?yàn)榇蠹叶贾?，干燥設備帶有火源（燃燒器和熱源）和燃料（產品、天-然氣、丙烷等）。

Shandong drying equipment . reasonable control method of oxygen in drying equipment: if there is no oxygen, the fire will not last for a long time. Therefore, by reducing the oxygen in the drying equipment, the fire risk can be reduced accordingly, which is a very important preventive measure. As we all know, drying equipment with fire (burner and heat source) and fuel (product, natural gas, propane, etc.).

作為干燥設備供應商，建議大多數干燥設備中的氧氣含量應保持盡可能低。在理想情況下，任何干燥設備中的氧氣含量應小于12％。如果在操作過程中氧氣含量超過該值，建議您使用以下方法：

?? as a drying equipment supplier, it is recommended that the oxygen content in most drying equipment should be kept as low as possible. Ideally, the oxygen content in any drying equipment should be less than 12%. If the oxygen content exceeds this value during operation, the following methods are recommended:

請將廢氣循環利用。這將增加蒸氣和惰性氣體的百分比，因此氧氣百分比將減少。尋找并修-復空氣泄漏的干燥設備。培訓操作員和維護人員以密封所有敞開的入口，以使?jié)L筒在密封的環境下保持工作。密封表面應光滑、圓潤。一定要記住，如果圓度變小，則不可能使密封面充分旋轉。

?? please recycle the waste gas. This will increase the percentage of vapor and inert gas, so the percentage of oxygen will decrease. Find and repair the drying equipment with air leakage. Train operators and maintenance personnel to seal all open entrances to keep the drum working in a sealed environment. The sealing surface shall be smooth and round. It is important to remember that if the roundness becomes smaller, it is not possible to make the sealing surface rotate fully.

當干燥設備旋轉時，如果其結構不完整，它將像水球在街上滾動一樣，變得越來越大。因此，需要建立必要的標準。

?? when the drying equipment rotates, if its structure is not complete, it will become larger and larger like a water ball rolling in the street. Therefore, the necessary standards need to be established.